MOFO-154X | 3000W 15-Inch Dual 4-Ohm VC Pro Subwoofer
3,000 Watt 15″ MOFO Series Subwoofer
MAX Power | 3,000 Watts |
---|---|
RMS Power | 1,700 Watts |
Impedance | DVC 4Ω |
Power Acoustik MOFO‑154X 15″ Subwoofer — Built for Bass Without Boundaries
The Power Acoustik MOFO‑154X is not your average subwoofer. Designed with SPL-focused performance, this 15-inch beast handles 3,000 watts max and 1,700 watts RMS with ease, built to deliver deep, low-frequency output without mechanical fatigue or thermal breakdown.
This model represents a precise balance between brute force and refined acoustics. Every component of the MOFO-Series X has been engineered to handle demanding car audio systems, especially in ported enclosures between 3–4 ft³, where deep bass extension and loudness are mission-critical.
Engineered for High SPL & Thermal Stability
At its core, the MOFO‑154X runs a 2.5″ dual 4-ohm voice coil with 4-layer winding and a 373 oz. motor volume—a configuration designed to push massive air while minimizing coil fatigue. The result? Substantial bass output, even under extended sessions at high volume.
Composite Cone with Structural Damping
The cone assembly fuses a polypropylene exterior layer with a non-pressed spruce pulp core, giving it the flexibility and acoustic absorption properties that optimize both bass response and cone stability. This structure reduces unwanted resonance, enabling cleaner low-end frequencies and tighter control under high excursion.
Integrated Heatsink: The Blue Dust Cap Advantage
The anodized aluminum dust cap is more than a visual marker—it’s part of a heat management system. Attached directly to the voice coil former, it acts as an active heatsink, pulling heat away from the core during operation. This means less thermal compression, more stable performance, and longer component life.
Mechanical Architecture Built to Last
- Die-cast aluminum frame prevents mechanical flex and supports rigid mounting
- Dual poly-cotton spiders stabilize cone movement across the entire excursion range
- High-temp adhesives hold the voice coil through punishing heat cycles
- UV-resistant polyether foam surround ensures linear motion without edge fatigue
- Nickel-plated, spring-loaded terminals accept 8-gauge speaker wire for low-resistance power transfer
Acoustic & Installation Specs
- Size: 15-inch
- Power Handling: 1,700W RMS / 3,000W Max
- Impedance: Dual 4Ω
- Efficiency: ~86.9 dB
- Mounting Depth: 8.125″
- Recommended Enclosure Volume:
- Sealed: ~2.0 ft³
- Ported: ~4.0 ft³
Overcompensating Motor Structure for Increased Magnetic Strength
12mm T-Yoke & Top Plate Improve Low-Frequency Dynamics
Vented T-Yoke & Frame Reduces Voice Coil Heat Build-up
Die-Cast Aluminum Heat Sink Dust Cap Absorbs Voice Coil Heat
Aluminum Dust Cap Fins Dissipate Heat & Strengthen Cone
Non-Magnetic Non-Resonate Die-Cast Aluminum Frame
2.5” 4-Layer Voice Coil w/ Large Gauge Wire Increases Power
High-Temperature Tolerance Adhesives Resist Thermal Failure
Nickel Plated 8ga Spring-Loaded Compression Wire Terminals
Non-Transfer Spruce Pulp Cone w/ UV & Chemical Protection
High-Density Polyether Foam Surround w/ UV & Chemical Protection
Dual Poly-Cotton Suspension Dampen Violent Accelerations
Stitched Voice Coil Leads Prevent Potential Damage
1-pc Gasket/Trim Ring w/ Concealed Mounting Holes Included
Specifications | MOFO-154X |
---|---|
Max Power Handling | 3,000 Watts |
RMS Power Handling | 1,700 Watts |
Efficiency (1w/1m) | 86.90 |
Voice Coil Configuration | 2.50″ Dual 4Ω |
Motor Volume | 373oz |
Mounting Depth | 8.125″ |
Optimum Sealed Enclosure ft3 | 2.00 |
Optimum Ported Enclosure ft3 | 4.00 |
placeholder